T11-FC-VIRTUAL-FABRIC-MIB DEFINITIONS ::= BEGIN
 
IMPORTS
    MODULE-IDENTITY, OBJECT-TYPE,
    Unsigned32, mib-2
                            FROM SNMPv2-SMI         -- [RFC2578]
    MODULE-COMPLIANCE, OBJECT-GROUP
                            FROM SNMPv2-CONF        -- [RFC2580]
    RowStatus, StorageType  FROM SNMPv2-TC          -- [RFC2579]
    InterfaceIndex          FROM IF-MIB             -- [RFC2863]
    fcmInstanceIndex, FcNameIdOrZero,
    fcmPortEntry, fcmSwitchEntry
                            FROM FC-MGMT-MIB        -- [RFC4044]
    T11FabricIndex          FROM T11-TC-MIB;        -- [RFC4439]
 
t11FcVirtualFabricMIB  MODULE-IDENTITY
    LAST-UPDATED    "200611100000Z"
    ORGANIZATION    "IETF IMSS (Internet and Management Support
                     for Storage) Working Group"
    CONTACT-INFO
            "
                     Scott Kipp
                     McDATA Corporation
                Tel: +1 720 558-3452
             E-mail: scott.kipp@mcdata.com
             Postal: 4 McDATA Parkway
                     Broomfield, CO USA 80021
 
                     G D Ramkumar
                     SnapTell, Inc.
                Tel: +1 650-326-7627
             E-mail: gramkumar@stanfordalumni.org
             Postal: 2741 Middlefield Rd, Suite 200
                     Palo Alto, CA USA 94306
 
                     Keith McCloghrie
                     Cisco Systems, Inc.
                Tel: +1 408 526-5260
             E-mail: kzm@cisco.com
             Postal: 170 West Tasman Drive
                     San Jose, CA USA 95134
            "
 
    DESCRIPTION
        "This module defines management information specific to
         Fibre Channel Virtual Fabrics.  A Virtual Fabric is a
 
 
 
         Fabric composed of partitions of switches, links and
         N_Ports with a single Fabric management domain, Fabric
         Services and independence from other Virtual Fabrics.
 
         Copyright (C) The IETF Trust (2006).  This version of
         this MIB module is part of RFC 4747; see the RFC itself for
         full legal notices."
    REVISION        "200611100000Z"
    DESCRIPTION
        "Initial version of this MIB module, published as RFC 4747."
    ::= { mib-2 147 }
 
t11vfObjects       OBJECT IDENTIFIER ::= { t11FcVirtualFabricMIB 1 }
t11vfConformance   OBJECT IDENTIFIER ::= { t11FcVirtualFabricMIB 2 }
 
--********************************
--  MIB object definitions
--
 
t11vfCoreSwitchTable  OBJECT-TYPE
    SYNTAX      SEQUENCE OF T11vfCoreSwitchEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of core switches supported by the current
         management entity."
    ::= { t11vfObjects 1 }
 
t11vfCoreSwitchEntry OBJECT-TYPE
    SYNTAX      T11vfCoreSwitchEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Each entry represents one core switch."
    INDEX   { fcmInstanceIndex, t11vfCoreSwitchSwitchName }
    ::= { t11vfCoreSwitchTable 1}
 
T11vfCoreSwitchEntry ::=
    SEQUENCE {
       t11vfCoreSwitchSwitchName   FcNameIdOrZero,
       t11vfCoreSwitchMaxSupported Unsigned32,
      t11vfCoreSwitchStorageType  StorageType
    }
 
t11vfCoreSwitchSwitchName OBJECT-TYPE
    SYNTAX      FcNameIdOrZero (SIZE(8 | 16))
    MAX-ACCESS  not-accessible
    STATUS      current
 
 
 
    DESCRIPTION
        "The Core Switch_Name (WWN) of this Core Switch."
    ::= { t11vfCoreSwitchEntry 1 }
 
t11vfCoreSwitchMaxSupported OBJECT-TYPE
    SYNTAX      Unsigned32 (1..4095)
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "In switches that do not support Virtual Fabrics,
         this object has the value of 1.  If Virtual Fabrics
         are supported, this object is the maximum number of
         Virtual Fabrics supported by the Core Switch.  For
         the purpose of this count, the Control VF_ID is
         ignored."
    ::= { t11vfCoreSwitchEntry 2 }
 
t11vfCoreSwitchStorageType OBJECT-TYPE
    SYNTAX      StorageType
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The storage type for this conceptual row.
         Conceptual rows having the value 'permanent' need not
         allow write-access to any columnar objects in the row."
    DEFVAL { nonVolatile }
    ::= { t11vfCoreSwitchEntry 3 }
 
-- Virtual Switch table
 
t11vfVirtualSwitchTable  OBJECT-TYPE
    SYNTAX      SEQUENCE OF T11vfVirtualSwitchEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of Virtual Switches.  When one Core Switch
         provides switching functions for multiple Virtual Fabrics,
         that Core Switch is modeled as containing multiple
         Virtual Switches, one for each Virtual Fabric.  This table
         contains one row for every Virtual Switch on every Core
         Switch.  This table augments the basic switch information in
         the fcmSwitchTable Table in the FC-MGMT-MIB."
    REFERENCE
        "fcmSwitchTable is defined in the FC-MGMT-MIB [RFC4044]."
    ::= { t11vfObjects 2 }
 
t11vfVirtualSwitchEntry OBJECT-TYPE
    SYNTAX      T11vfVirtualSwitchEntry
 
 
 
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry of the Virtual Switch table.  Each row is for a
         Virtual Switch.
 
         This table augments the fcmSwitchTable, i.e., every entry
         in this table has a one-to-one correspondence with an
         entry in the fcmSwitchTable.  At the time when the
         fcmSwitchTable was defined, it applied to physical
         switches.  With the definition and usage of virtual
         switches, fcmSwitchTable now applies to virtual switches
         as well as physical switches, and (in contrast to physical
         switches) it is appropriate to provide the capability for
         virtual switches to be created via remote management
         applications, e.g., via SNMP.
 
         So, this entry contains a RowStatus object (to allow the
         creation of a virtual switch), as well as a StorageType
         object.  Obviously, if a row is created/deleted in this
         table, the corresponding row in the fcmSwitchTable will
         be created/deleted."
    REFERENCE
        "fcmSwitchEntry is defined in the FC-MGMT-MIB module
         [RFC4044]."
    AUGMENTS   { fcmSwitchEntry }
    ::= { t11vfVirtualSwitchTable 1}
 
T11vfVirtualSwitchEntry ::=
    SEQUENCE {
        t11vfVirtualSwitchVfId               T11FabricIndex,
        t11vfVirtualSwitchCoreSwitchName     FcNameIdOrZero,
        t11vfVirtualSwitchRowStatus          RowStatus,
        t11vfVirtualSwitchStorageType       StorageType
    }
 
t11vfVirtualSwitchVfId OBJECT-TYPE
    SYNTAX      T11FabricIndex
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The VF_ID of the Virtual Fabric for which this virtual
         switch performs its switching function.  The Control
         VF_ID is implicitly enabled and is not set.
         Communication with the Control VF_ID is required."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.2"
    ::= { t11vfVirtualSwitchEntry 1 }
 
 
 
 
t11vfVirtualSwitchCoreSwitchName OBJECT-TYPE
    SYNTAX      FcNameIdOrZero (SIZE(8 | 16))
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "The Core Switch_Name (WWN) of the Core Switch that
         contains this Virtual Switch."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.2."
    ::= { t11vfVirtualSwitchEntry 2 }
 
t11vfVirtualSwitchRowStatus OBJECT-TYPE
        SYNTAX      RowStatus
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The status of this row."
        ::= { t11vfVirtualSwitchEntry 3 }
 
t11vfVirtualSwitchStorageType OBJECT-TYPE
    SYNTAX      StorageType
    MAX-ACCESS  read-create
    STATUS      current
    DESCRIPTION
        "The storage type for this conceptual row.
         Conceptual rows having the value 'permanent' need not
         allow write-access to any columnar objects in the row."
    DEFVAL { nonVolatile }
    ::= { t11vfVirtualSwitchEntry 4 }
 
-- Port table
 
t11vfPortTable OBJECT-TYPE
    SYNTAX      SEQUENCE OF T11vfPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table of Port attributes related to Virtual Fabrics."
    ::= { t11vfObjects 3 }
 
t11vfPortEntry OBJECT-TYPE
    SYNTAX      T11vfPortEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "Each entry represents a physical Port on a switch.
         Switches that support Virtual Fabrics would add
 
 
 
         these four additional columns to the fcmPortEntry
         row."
    REFERENCE
        "fcmPortEntry is defined in the FC-MGMT-MIB module."
    AUGMENTS   { fcmPortEntry }
    ::= { t11vfPortTable 1}
 
T11vfPortEntry ::=
    SEQUENCE {
        t11vfPortVfId                T11FabricIndex,
        t11vfPortTaggingAdminStatus   INTEGER,
        t11vfPortTaggingOperStatus    INTEGER,
        t11vfPortStorageType        StorageType
    }
 
t11vfPortVfId OBJECT-TYPE
    SYNTAX      T11FabricIndex
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The Port VF_ID assigned to this Port.  The Port VF_ID is the
         default Virtual Fabric that is assigned to untagged frames
         arriving at this Port.  The Control VF_ID is implicitly
         enabled and is not set.  Communication with the Control
         VF_ID is required."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.1"
    DEFVAL    {1}
    ::= { t11vfPortEntry 1 }
 
t11vfPortTaggingAdminStatus OBJECT-TYPE
    SYNTAX INTEGER {
        off(1),
        on(2),
        auto(3)
    }
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "This object is used to configure the administrative status
         of Virtual Fabric tagging on this Port.
 
         SET operation   Description
         --------------  -------------------------------------------
         off(1)          To disable Virtual Fabric tagging on this
                         Port.
 
         on(2)           To enable Virtual Fabric tagging on this
 
 
 
                         Port if the attached Port doesn't
                         prohibit it.
 
         auto(3)         To enable Virtual Fabric tagging if the
                         peer requests it."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.4"
    ::= { t11vfPortEntry 2 }
 
 t11vfPortTaggingOperStatus OBJECT-TYPE
    SYNTAX INTEGER {
        off(1),
        on(2)
            }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object is used to report the operational status of
         Virtual Fabric tagging on this Port.
 
         SET operation   Description
         --------------  -------------------------------------------
         off(1)          Virtual Fabric tagging is disabled on this
                         Port.
 
         on(2)           Virtual Fabric tagging is enabled on this
                         Port."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.4"
    ::= { t11vfPortEntry 3 }
 
t11vfPortStorageType OBJECT-TYPE
    SYNTAX      StorageType
    MAX-ACCESS  read-write
    STATUS      current
    DESCRIPTION
        "The storage type for this conceptual row, and for the
         corresponding row in the augmented fcmPortTable.
 
         Conceptual rows having the value 'permanent' need not
         allow write-access to any columnar objects in the row."
    DEFVAL { nonVolatile }
    ::= { t11vfPortEntry 4 }
 
 
-- Locally Enabled Table
 
t11vfLocallyEnabledTable OBJECT-TYPE
 
 
 
    SYNTAX      SEQUENCE OF T11vfLocallyEnabledEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A table for assigning and reporting operational status of
         locally-enabled Virtual Fabric IDs to Ports.  The set of
         Virtual Fabrics operational on the Port is the bit-wise
         'AND' of the set of locally-enabled VF_IDs of this Port
         and the locally-enabled VF_IDs of the attached Port."
    ::= { t11vfObjects 4 }
 
t11vfLocallyEnabledEntry OBJECT-TYPE
    SYNTAX      T11vfLocallyEnabledEntry
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "An entry for each locally-enabled VF_ID on
         each Port."
    REFERENCE
        "FC-SW-4, REV 7.5, section 12.4"
    INDEX { t11vfLocallyEnabledPortIfIndex, t11vfLocallyEnabledVfId }
 
    ::= { t11vfLocallyEnabledTable 1}
 
T11vfLocallyEnabledEntry ::=
    SEQUENCE {
        t11vfLocallyEnabledPortIfIndex    InterfaceIndex,
        t11vfLocallyEnabledVfId           T11FabricIndex,
        t11vfLocallyEnabledOperStatus     INTEGER,
        t11vfLocallyEnabledRowStatus      RowStatus,
        t11vfLocallyEnabledStorageType    StorageType
    }
 
t11vfLocallyEnabledPortIfIndex OBJECT-TYPE
    SYNTAX      InterfaceIndex
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "The value of the ifIndex that identifies the Port."
    ::= { t11vfLocallyEnabledEntry 1 }
 
t11vfLocallyEnabledVfId OBJECT-TYPE
    SYNTAX      T11FabricIndex
    MAX-ACCESS  not-accessible
    STATUS      current
    DESCRIPTION
        "A locally-enabled VF_ID on this Port."
    ::= { t11vfLocallyEnabledEntry 2 }
 
 
 
 
t11vfLocallyEnabledOperStatus OBJECT-TYPE
    SYNTAX INTEGER {
        off(1),
        on(2)
            }
    MAX-ACCESS  read-only
    STATUS      current
    DESCRIPTION
        "This object is used to report the operational status of
         Virtual Fabric tagging on this Port.
 
         SET operation   Description
         --------------  -------------------------------------------
         off(1)          Virtual Fabric tagging is disabled on this
                         Port.
 
         on(2)           Virtual Fabric tagging is enabled on this
                         Port."
    REFERENCE
        "FC-SW-4, REV 7.3, section 12.4"
    ::= { t11vfLocallyEnabledEntry 3 }
 
t11vfLocallyEnabledRowStatus OBJECT-TYPE
        SYNTAX      RowStatus
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The status of this conceptual row.
 
             When a row in this table is in 'active(1)' state,
             no object in that row can be modified except
             t11vfLocallyEnabledRowStatus and
             t11vfLocallyEnabledStorageType."
        ::= { t11vfLocallyEnabledEntry 4 }
 
t11vfLocallyEnabledStorageType OBJECT-TYPE
        SYNTAX      StorageType
        MAX-ACCESS  read-create
        STATUS      current
        DESCRIPTION
            "The storage type for this conceptual row.
             Conceptual rows having the value 'permanent' need not
             allow write-access to any columnar objects in the row."
        DEFVAL { nonVolatile }
        ::= { t11vfLocallyEnabledEntry 5 }
 
--********************************
 
 
 
-- Conformance Section
--
 
t11vfMIBCompliances OBJECT IDENTIFIER ::= { t11vfConformance 1 }
t11vfMIBGroups      OBJECT IDENTIFIER ::= { t11vfConformance 2 }
 
t11vfMIBCompliance MODULE-COMPLIANCE
    STATUS  current
    DESCRIPTION
        "Describes the requirements for compliance to the
         Fibre Channel Virtual Fabric MIB."
    MODULE  -- this module
        MANDATORY-GROUPS { t11vfGeneralGroup }
 
        OBJECT t11vfCoreSwitchMaxSupported
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfCoreSwitchStorageType
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfVirtualSwitchVfId
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfVirtualSwitchRowStatus
        SYNTAX RowStatus { active(1) }
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfVirtualSwitchStorageType
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfPortVfId
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfPortTaggingAdminStatus
        MIN-ACCESS read-only
        DESCRIPTION
 
 
 
            "Write access is not required."
 
        OBJECT t11vfPortStorageType
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfLocallyEnabledRowStatus
        SYNTAX       RowStatus { active(1) }
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
        OBJECT t11vfLocallyEnabledStorageType
        MIN-ACCESS read-only
        DESCRIPTION
            "Write access is not required."
 
    ::= { t11vfMIBCompliances 1 }
 
-- Units of conformance
 
    t11vfGeneralGroup  OBJECT-GROUP
        OBJECTS { t11vfCoreSwitchMaxSupported,
                  t11vfVirtualSwitchVfId,
                  t11vfVirtualSwitchCoreSwitchName,
                  t11vfVirtualSwitchRowStatus,
                  t11vfPortVfId,
                  t11vfPortTaggingAdminStatus,
                  t11vfLocallyEnabledOperStatus,
                  t11vfPortTaggingOperStatus,
                  t11vfLocallyEnabledRowStatus,
               t11vfCoreSwitchStorageType,
                   t11vfVirtualSwitchStorageType,
                  t11vfPortStorageType,
                  t11vfLocallyEnabledStorageType
 
        }
        STATUS current
        DESCRIPTION
            "A collection of objects for monitoring and
             configuring Virtual Fabrics in a Fibre Channel switch."
        ::= { t11vfMIBGroups 1 }
 
END